ASE G1 Maintenance & Light Repair practice test

G1 is the entry-level certification and the widest one on the list: it touches every system on the car, but at the depth a maintenance and light-repair technician actually works. Fewer deep diagnostics, far more range.

G1 Maintenance & Light Repair Question 1 of 10

In an SAE 5W-30 rating, what does the W indicate?

Worked examples from the G1 bank

8 of the 30 questions in this bank, with the answer marked and the reasoning written out — the same explanation the practice test shows after each answer. Read these first if you want to see what the test asks before you start the run above.

  1. 1. A vehicle squeals while driving but the noise stops when the brakes are applied. This is MOST likely:

    • A. A wear indicator contacting the rotor ✓
    • B. Air in the hydraulic system
    • C. A failing wheel bearing
    • D. A warped rotor

    Why: The mechanical wear tab drags on the rotor as the pad thins and is pushed away from it when the pad clamps down — which is exactly why the squeal disappears under braking.

  2. 2. A 12-volt lead-acid battery at rest measures 12.6 volts. This indicates the battery is:

    • A. Fully charged ✓
    • B. About 50 percent charged
    • C. Discharged
    • D. Overcharged and gassing

    Why: Roughly 12.6 volts open-circuit is a full charge; about 12.4 is 75 percent and 12.2 is around 50 percent. State of charge must be judged at rest, after any surface charge is removed.

  3. 3. With the engine running at about 2,000 rpm and a moderate electrical load, charging-system voltage at the battery should typically be:

    • A. 10.5–11.5 volts
    • B. 12.0–12.6 volts
    • C. 13.5–14.5 volts ✓
    • D. 16.0–17.0 volts

    Why: The charging system has to sit above battery voltage to push current back in. Readings near battery voltage suggest it is not charging; readings much higher suggest a regulation fault.

  4. 4. A blown 15-amp fuse keeps failing. The technician should:

    • A. Install a 20-amp fuse to stop the nuisance blowing
    • B. Install a 15-amp fuse and diagnose the circuit for the fault ✓
    • C. Bypass the fuse with a jumper wire for testing
    • D. Install a circuit breaker of any rating

    Why: The fuse is sized to protect the wiring. Raising the rating lets the wire become the fuse, which is how harness fires start. The repeated failure is the symptom to diagnose.

  5. 5. White-green corrosion on a battery terminal is commonly neutralized with:

    • A. A baking soda and water solution ✓
    • B. Brake cleaner
    • C. Fresh electrolyte
    • D. Penetrating oil

    Why: The corrosion is acidic, so a mild base neutralizes it. Keep the solution out of the cells, rinse afterwards, and protect the clean terminal to slow it coming back.

  6. 6. When testing for a parasitic draw, the ammeter is connected:

    • A. In parallel across the battery terminals
    • B. In series between the disconnected battery cable and the battery post ✓
    • C. Across the alternator output terminal and ground
    • D. In series with the starter cable only

    Why: Current measurement requires the meter to be in the current path, so the meter goes in series where the cable was. Connecting an ammeter in parallel across the battery creates a short through the meter.

  7. 7. A blower motor operates on the highest speed only. The MOST likely cause is:

    • A. A failed blower motor
    • B. A failed blower motor resistor or its circuit ✓
    • C. A plugged cabin air filter
    • D. A low refrigerant charge

    Why: High speed usually bypasses the resistor and feeds the motor directly, so losing every speed except high points at the resistor. A dead motor would produce no speeds at all.

  8. 8. A vehicle is labelled for R-1234yf refrigerant. Servicing it with R-134a is:

    • A. Acceptable if the system is fully evacuated first
    • B. Acceptable with an adapter fitting
    • C. Not acceptable — refrigerants and their equipment are not interchangeable ✓
    • D. Acceptable only in cooler climates

    Why: Systems are designed and labelled for one refrigerant, service fittings are deliberately different, and recovery equipment is refrigerant-specific. Cross-charging contaminates both the vehicle and the shop’s recovery machine.

How the G1 test works

55 scored questions

+ ~10 unscored research questions

90 minutes

computer-based, at a test center

$62 per test

plus one $34 registration fee per order

Valid 5 years

then a shorter recertification test

ASE does not publish one universal passing percentage; the passing standard is set by test. TorquePrep uses 80% as a conservative practice target, not as an official ASE cut score. The certificate is issued once ASE verifies your required work experience.

What the G1 test covers

The official task list for G1 Auto Maintenance and Light Repair breaks down into these content areas — the practice bank above draws from all of them:

  • Engine systems — oil and filter service, cooling system, belts, and basic diagnosis
  • Automatic transmission and transaxle — fluid level, condition, and service
  • Manual drive train and axles — clutch, CV joints, and lubricant service
  • Suspension and steering — tires, TPMS, alignment symptoms, and wear checks
  • Brakes — pad and rotor measurement, hydraulic service, and common noise diagnosis
  • Electrical — battery, charging, circuit protection, and lighting
  • Heating and air conditioning — airflow, blower circuits, and refrigerant handling

Frequently asked

How many questions are on the ASE G1 test?
The G1 test has 55 scored questions plus about 10 unscored research questions, with a 90-minute time limit.
Is G1 a good first ASE test?
For most technicians, yes. G1 is written around maintenance and light-repair work rather than deep diagnostics, so it matches what an entry-level tech does daily — and it touches every system, which makes it useful preparation for the A-series later.
Does G1 count toward Master Automobile Technician?
No. Master Automobile Technician status comes from passing A1 through A8. G1 is a standalone certification aimed at the maintenance and light-repair role.
Is G1 easier than the A-series tests?
It is broader but shallower. You will see something from nearly every system, but the questions stay at service depth rather than asking you to diagnose an intermittent fault down to a component.

Exam length, timing, fees, and content areas checked September 11, 2026 against the official ASE test table and ASE study guides.

Other ASE practice tests