ASE A6 Electrical practice test

The A6 test is the biggest of the A-series — 50 scored questions and 90 minutes — and widely called the hardest. It rewards real circuit reasoning: Ohm’s law, voltage-drop testing, and working through battery, starting, charging, and body-electrical faults.

A6 Electrical Systems Question 1 of 10

A technician measures excessive AC ripple voltage at the alternator output terminal with the engine running and loads applied. Which is the most likely cause?

Worked examples from the A6 bank

8 of the 30 questions in this bank, with the answer marked and the reasoning written out — the same explanation the practice test shows after each answer. Read these first if you want to see what the test asks before you start the run above.

  1. 1. The left low-beam headlamp is noticeably dimmer than the right. Technician A says a corroded ground connection at the left lamp could be the cause. Technician B says a faulty headlamp switch is the most likely cause. Who is correct?

    • A. A only ✓
    • B. B only
    • C. Both A and B
    • D. Neither A nor B

    Why: Resistance in one lamp’s own feed or ground drops voltage only at that lamp, dimming it alone. A faulty headlamp switch is common to both lamps and would affect both sides, so Technician B is wrong.

  2. 2. The right-side turn signals flash much faster than the left side on a vehicle with a conventional load-sensitive flasher. Which is the most likely cause?

    • A. A defective flasher unit
    • B. A burned-out bulb on the right side ✓
    • C. A blown turn-signal fuse
    • D. A poor ground at the steering column

    Why: A load-sensitive flasher changes rate when circuit current changes, so a burned-out bulb on one side makes that side flash fast (or on some designs, not at all). A defective flasher or blown fuse would affect both sides.

  3. 3. A fuel gauge always reads empty regardless of tank level. Technician A says this proves the tank sender unit is open. Technician B says substituting a known resistance value for the sender at its connector will show whether the gauge and wiring respond correctly. Who is correct?

    • A. A only
    • B. B only ✓
    • C. Both A and B
    • D. Neither A nor B

    Why: An always-empty reading can come from the sender, the wiring, or the gauge itself, and whether an open sender reads empty or full depends on the system design — so nothing is "proved" yet. Substituting a known resistance (or a gauge tester) isolates the sender from the rest of the circuit.

  4. 4. All of the analog gauges in an instrument cluster read erratically at the same time, sweeping up and down together while driving. Which is the most likely cause?

    • A. A faulty fuel tank sender unit
    • B. A defective coolant temperature sensor
    • C. A blown cluster illumination fuse
    • D. A poor ground or power connection shared by the instrument cluster ✓

    Why: A single sender only affects its own gauge; when every gauge misbehaves together, suspect what they share — the cluster’s common power feed, ground, or internal voltage reference. Checking cluster connector voltage drops is the standard next step.

  5. 5. A horn does not sound when the horn pad is pressed. When battery voltage is jumped directly to the horn’s terminal with its ground still connected, the horn sounds normally. Which area should the technician diagnose next?

    • A. The horn itself
    • B. The horn’s mounting-bracket ground
    • C. The battery state of charge
    • D. The horn control circuit — switch, relay, and wiring ✓

    Why: Sounding on jumped power with its normal ground proves the horn and its ground path are good. The fault must be upstream in the control side: horn pad switch, clockspring, relay, or feed wiring.

  6. 6. Windshield wipers work on all speeds, but when switched off they stop immediately wherever they happen to be instead of returning to the base of the windshield. Which is the most likely cause?

    • A. A defective park switch circuit in the wiper motor assembly ✓
    • B. A worn wiper transmission linkage
    • C. A blown wiper circuit fuse
    • D. A defective multifunction switch high-speed contact

    Why: The park switch inside the motor assembly keeps feeding the motor after the driver switches off, until the arms reach the park position. If that circuit fails, the wipers die in place; linkage or fuse faults would show different symptoms.

  7. 7. With the battery disconnected, a technician measures resistance between the CAN high and CAN low wires at the data link connector on a high-speed CAN bus with two 120-ohm terminating resistors. What reading indicates a normal bus?

    • A. About 120 ohms
    • B. About 60 ohms ✓
    • C. About 0 ohms
    • D. Out of range (open)

    Why: The two 120 Ω terminating resistors sit in parallel across the bus, so a healthy network reads approximately 60 Ω. About 120 Ω suggests one terminator or its wiring is open, near 0 Ω means the bus wires are shorted together.

  8. 8. Two technicians are discussing module communication faults. Technician A says a data bus wire shorted to ground can cause a loss of communication with every module on that bus. Technician B says when only one module is offline while the others communicate normally, that module’s power, ground, and bus connections are the prime suspects. Who is correct?

    • A. A only
    • B. B only
    • C. Both A and B ✓
    • D. Neither A nor B

    Why: The bus is shared, so a wire shorted to ground or to voltage can silence every module on it, while a single silent module points to its own supply, ground, or connector. Both statements describe standard network triage.

How the A6 test works

50 scored questions

+ ~10 unscored research questions

90 minutes

computer-based, at a test center

$62 per test

plus one $34 registration fee per order

Valid 5 years

then a shorter recertification test

ASE does not publish one universal passing percentage; the passing standard is set by test. TorquePrep uses 80% as a conservative practice target, not as an official ASE cut score. The certificate is issued once ASE verifies your required work experience.

What the A6 test covers

The official task list for A6 Electrical/Electronic Systems breaks down into these content areas — the practice bank above draws from all of them:

  • General electrical diagnosis — Ohm’s law, series/parallel circuits, voltage drop, and meter use
  • Battery — state of charge, load and conductance testing, and parasitic draw
  • Starting system — current draw and slow-crank diagnosis
  • Charging system — output testing and voltage regulation
  • Lighting, gauges, driver information, and body electrical accessories
  • Data bus and module communication basics

Frequently asked

How many questions are on the ASE A6 test?
The A6 test has 50 scored questions plus about 10 unscored research questions, with a 90-minute time limit — the longest of the A-series.
How much math is on A6?
Expect a handful of simple Ohm’s-law and voltage-drop calculations — single-step arithmetic, not algebra. The harder questions are meter-reading interpretations.
Why is A6 considered the hardest A-series test?
It covers every electrical system on the vehicle and demands circuit-level reasoning rather than pattern recognition. Solid voltage-drop testing habits are the best preparation.

Exam length, timing, fees, and content areas checked September 11, 2026 against the official ASE test table and ASE study guides.

Other ASE practice tests